Home › GE Monogram Error Codes › Dishwasher Not Draining
Serving the Denver metro

GE Monogram Dishwasher Not Draining — What It Means

What dishwasher not draining means, common causes, and whether it's something you can check yourself before calling for service.

Call (720) 674-7147
★ 4.8 (256+ reviews)
Same-day service
IMAGE PLACEHOLDER
Dishwasher Not Draining
Skilled & Experienced
Licensed & Insured
Genuine OEM Parts
Up to 1-Yr Warranty

Likely Causes

A clogged filter or drain line

The single most common cause of drainage and cleaning-performance complaints.

A failed door latch or control fault

Many dishwashers won't start at all if the door sensor doesn't register a full, secure close.

A worn spray arm or pump

Reduced water pressure inside the tub shows up as dishes that aren't getting properly cleaned or rinsed.

Quick Checks You Can Try

1
Check and clean the filter at the bottom of the tub
2
Confirm the door latches fully and the cycle selector is set correctly

Parts That Most Likely Need Replacing

Based on this code, these are the components our technicians check first. The exact part depends on your model and what we find during diagnosis.

Drain Pump
Door Latch Switch
Wash Pump / Spray Arm Assembly

Seeing this code?

Same-day diagnosis, genuine OEM-compatible parts, warranty of up to 1 year.

Call (720) 674-7147
Related Error Codes
→Dishwasher Leak/Fill Fault →F0/F1 Family (Control Board Runaway) →F2 All GE Monogram error codes →
Related Problems
→Dishwasher Leak Fill Fault →Dishwasher Won't Drain →Dishwasher Won't Start All GE Monogram problems →

Common Questions About Dishwasher Not Draining

Can I keep using my GE Monogram appliance while this shows?
If it's still working normally, short-term use usually isn't harmful — but a persistent fault means something is actively failing, and continuing to run the unit can turn a smaller repair into a larger one. We'd recommend having it looked at within a few days rather than waiting until it stops working entirely.
Does clearing the code mean the problem is fixed?
Not necessarily. A power cycle can clear a code from the display without resolving whatever triggered it, especially for intermittent sensor faults. If it comes back within a few hours or days, that's confirmation the underlying issue is still there.
How much does this repair typically cost?
It depends on which component is at fault. We charge a flat diagnostic fee and provide a firm quote before any repair work begins — see our repair pricing page for typical ranges.
How long does a typical repair visit take?
Most single-component repairs are completed in one visit, often within an hour or two once the part is confirmed. We'll give you a specific estimate after diagnosis.
Do you offer a warranty on the repair?
Yes — every repair includes a written warranty of up to 1 year on parts and labor.
Do you service GE Monogram appliances in my area?
Likely yes — we cover Denver and 143 surrounding cities. See our full service area list to confirm.

Still seeing this code?

Same-day diagnosis, genuine OEM-compatible parts, warranty of up to 1 year.

Call (720) 674-7147
Sub-Zero Repair Denver
Colorado

Independent Sub-Zero, Wolf & Viking appliance repair across Denver. Skilled technicians, OEM-compatible parts, transparent pricing.

(720) 674-7147
Denver, CO · Mon–Sat, 7am–7pm
Areas
Denver Cherry Hills Village Greenwood Village Boulder All Areas →
Brands
Sub-Zero Wolf Viking Thermador All Brands →
Support & Help Problems Troubleshooting Error Codes Repair or Replace Authorized & Certified OEM Parts Repair Cost
Company
About Reviews Contact Terms Privacy

*SubZero Repair Denver is an independent repair company and is not affiliated in any way with Sub-Zero, Inc., Wolf Appliance, Inc., or any of their distributors. We are not a factory service provider and specialize exclusively in out-of-warranty appliance repairs.

© 2026 SubZero Repair Denver. All rights reserved.
2055 S Oneida St, Denver, CO 80224 · (720) 674-7147
Call (720) 674-7147